Material Selection
Somaloy Alternatives
How to Source Equivalent Soft Magnetic Composite (SMC) Components — What engineers and buyers actually need when they search for a Somaloy alternative: the grade logic behind 1P/3P/5P, which properties define equivalence, and how to source SMC parts from non-Höganäs powder supply

Yao Qingpu
Powder Metallurgy Manufacturing Expert at SinterWorks PM
Table of Contents
Quick Answer
Somaloy is Höganäs AB's trademarked family of soft magnetic composite (SMC) powders — insulated iron powder compacted into motor cores and electromagnetic components. A true Somaloy alternative is not a single product but an equivalence exercise: match the insulation coating system, compaction pressure, permeability (typically 500–800 for common grades), core loss at your operating frequency, and cured density (around 7.3–7.6 g/cm3). Equivalent SMC components can be produced by independent PM manufacturers using other insulated iron powders or in-house coating processes, provided the magnetic specification is defined by measured properties rather than by brand name.
Key Takeaways
- Somaloy is a brand, not a material class — the material class is soft magnetic composite (SMC): iron particles with an electrically insulating coating, pressed and cured rather than sintered.
- The Somaloy naming logic encodes processing: 1P/3P/5P describe coating and heat-treatment routes that trade core loss against mechanical strength and cost.
- Equivalence is defined by four numbers: maximum permeability, core loss at your frequency and flux density, cured density, and transverse rupture strength — not by the powder brand.
- Independent PM manufacturers can compact SMC components from non-Höganäs insulated powders (or in-house coated iron powder), which is often where cost and lead-time flexibility come from.
- Write the specification as a magnetic performance target (B-H curve and W/kg at frequency), and let suppliers propose powder systems against it.
Introduction
If you typed "Somaloy alternative" into a search engine, you are probably in one of three situations: your current SMC cores are getting expensive at volume, you are uncomfortable single-sourcing a branded powder, or you are designing a new motor and want to know what the soft magnetic composite market actually looks like beyond one supplier.
This guide answers that properly. We manufacture soft magnetic components by powder metallurgy, so this is written from the production side: what Somaloy actually is, what "equivalent" must mean technically, and how to source SMC components without locking yourself to a brand. For the material fundamentals, see our soft magnetic composites overview; this article is about sourcing strategy.
What Somaloy Actually Is
Somaloy is the trademarked SMC powder family from Höganäs AB, the Swedish metal powder producer. The underlying material concept is not proprietary in principle: take high-purity iron powder, coat every particle with a thin electrically insulating layer (phosphate-based, organic, or hybrid), compact the powder at high pressure into a net-shape core, and cure or stress-relieve it at low temperature. The insulation suppresses eddy currents in all three spatial directions, which is what frees motor designers from the 2D flux constraint of laminated steel.
Two things about this matter for sourcing:
- The value is in the coating and the process window, not the iron. Any alternative must reproduce coating integrity after 600–800+ MPa of compaction pressure.
- SMC cores are cured, not sintered. Conventional sintering temperatures would destroy the insulation. This is why SMC production is a specialized PM capability — see how we make soft magnetic components.
Decoding the Grade Names: 1P, 3P, 5P, and the Numbers
The Somaloy naming system encodes the processing route, and understanding it tells you exactly what to ask an alternative supplier for:
- 1P — one compaction plus a single low-temperature treatment in air. The economical baseline: good mechanical strength, permeability typically up to the mid-hundreds, highest core loss of the family.
- 3P — adds a coating and heat-treatment step that improves permeability (commonly cited around 700) with strong mechanical properties and moderate loss. The mainstream motor choice.
- 5P — a higher-temperature anneal route delivering the lowest core loss, suited to higher-frequency designs (up to roughly 1,000 Hz class applications), at the highest processing cost.
The numeric names (500, 700, 700HR, 1000 series) indicate permeability class and base powder. Published data for the 700HR 5P grade, for example, shows core loss on the order of 65 W/kg at 1.5 T and 400 Hz, with densities near 7.5 g/cm3 — use figures like these as your reference points when comparing alternatives, always measured at your operating point.
The Four Numbers That Define Equivalence
A credible Somaloy alternative is defined by measured properties, not marketing names. When evaluating any substitute supply, lock these four:
- Maximum permeability at your working induction — drives how much magnetomotive force (and copper) the design needs.
- Core loss in W/kg at your frequency and peak flux density — the efficiency number. Compare at 50/200/400/800 Hz as relevant; SMC typically trails laminations at grid frequency and overtakes them above a few hundred Hz.
- Cured density — correlates with both permeability and strength; high-performance cores sit around 7.3–7.6 g/cm3.
- Mechanical strength (transverse rupture or specified handling loads) — SMC is weaker than structural PM steel; confirm it survives press-fitting of magnets and assembly forces.
If a supplier can produce test rings or prototype cores measured against these four numbers, the brand of powder behind them is a secondary question.
Where Alternatives Actually Come From
Three realistic supply routes exist:
- Other branded insulated powders. A small number of global powder producers offer SMC-type powders with published data sheets. These are the most direct drop-in path.
- In-house coated iron powder. Some PM component manufacturers apply proprietary insulation coatings to water-atomized iron powder and compact the cores themselves. This route often wins on cost and lead time at volume, and it decouples you from any powder brand — but it makes the supplier's process control the critical qualification item.
- Adjacent material classes where they genuinely fit. Fe-Si powder cores, ferrites, or thin-gauge laminations solve some of the same problems. Be honest about the trade: none of them match SMC's 3D flux freedom in a single pressed piece, which is usually why SMC was chosen in the first place. Our SMC for electric motors page maps where each route wins, and the axial-flux motor deep dive covers the highest-growth SMC application.
How to Second-Source Without Regretting It
A practical qualification sequence:
- Document the incumbent properly. Pull the actual magnetic requirement from the motor model: operating frequency, peak B, loss budget, geometry constraints. "Same as Somaloy 700 3P" is not a specification.
- Request measured data, not brochures. Ask candidate suppliers for toroid or prototype-core measurements at your operating point, plus density and strength data.
- Prototype in real tooling. SMC properties are path-dependent — compaction pressure, tooling fill, and cure cycle all move the numbers. A lab toroid is a screen; a pressed prototype core is evidence.
- Run a comparative motor test. Published research on axial-flux prototypes shows that powder-state superiority does not always survive compaction and assembly; motor-level dynamo testing is the only final arbiter.
- Then negotiate volume economics. With two qualified sources, the pricing conversation changes completely.
Conclusion
Searching for a Somaloy alternative is really searching for a way to specify soft magnetic composite performance independent of a brand. The material class is well understood, the equivalence criteria are four measurable numbers, and independent PM manufacturers can produce SMC cores from alternative or in-house coated powders. The companies that do this successfully treat it as a metrology exercise first and a purchasing exercise second.
Evaluating SMC for a Motor or Electromagnetic Component?
Send your core geometry, frequency range, flux density target, and annual volume through our quote page. We will review compaction feasibility, propose a powder and coating route, and benchmark expected permeability and core loss against your incumbent material — branded or not. For a production example, see our EV motor rotor case study.
Related Resources
Use these internal guides to keep exploring process planning, materials, quality control, and quoting steps for this topic.
FC-0208 Material Guide: Properties, Applications, and When to Use It in Powder Metallurgy
Learn what FC-0208 means in powder metallurgy, where it is commonly used, how it compares with FC-0205 and FN-0205, and when it is the right choice for gears and structural parts.
Metal Injection Molding Materials: Stainless, Low-Alloy, Tool Steel, and Specialty Alloys for MIM
Not every metal powder feeds cleanly through an injection molding barrel and sinters to full density. Learn which materials work in MIM, their typical mechanical properties, and how to pick the right alloy for medical, automotive, aerospace, and consumer applications.
Copper Powder Types for Powder Metallurgy: Electrolytic vs Atomized vs Reduced
Electrolytic, water-atomized, gas-atomized, and reduced copper powders behave very differently in the press and furnace.
Steel Powder Metallurgy Guide: Grades, Properties, and When to Choose PM Steel
Steel powder metallurgy turns iron powder plus carbon and alloying elements into net-shape sintered steel parts. This guide covers PM steel grades, heat treatment, and when PM steel is the right choice.
Frequently Asked Questions
Is Somaloy the only soft magnetic composite powder available?
No. Somaloy (Höganäs) is the best-known SMC powder family, but other powder producers offer insulated iron powders, and some PM component manufacturers apply their own insulation coatings to water-atomized iron powder. What matters for the finished core is the measured permeability, core loss, and density — not the powder brand.
What do Somaloy 1P, 3P, and 5P mean?
They describe processing routes. In broad terms, 1P is a single compaction plus low-temperature treatment optimized for economy and strength; 3P adds a coating and heat-treatment step that raises permeability and lowers loss; 5P uses a higher-temperature anneal for the lowest core loss of the three, at higher cost. Any alternative supply should be evaluated against the same processing intent.
Can I switch from Somaloy to an alternative without redesigning my motor?
Usually the tooling and geometry can stay, because SMC components are defined by the pressed shape. What must be re-validated is the magnetic performance: permeability and core loss curves of the alternative material at your operating point, plus mechanical strength if the core is load-bearing. Budget for comparative loss measurements before committing production volumes.
Why do companies look for Somaloy alternatives at all?
The common drivers are cost pressure at high volume, supply-chain diversification (single-source risk on a branded powder), lead time, and regional sourcing preferences. Because SMC is a process-and-property specification rather than a chemistry patent wall, second-sourcing is technically straightforward when the target properties are documented.
What should I send a supplier to quote an SMC core?
Core geometry (STEP file), operating frequency range, peak flux density target, core loss budget in W/kg at that operating point, required permeability, mechanical loads if any, and annual volume. That package lets the supplier match a powder system and compaction route — whether or not it carries a brand name.
Standards & References
Industry standards cited in this article are published and maintained by the following bodies. For critical applications, verify against the current edition:
- MPIF Standard 35 and PM test standards — Metal Powder Industries Federation
- ASTM International — metal powder and PM material specifications
- ISO 5755: Sintered metal material — Specifications — ISO
Expert Review
Yao Qingpu
Powder Metallurgy Manufacturing Expert at SinterWorks PM
Yao Qingpu works with global buyers on powder metallurgy design review, material selection, tolerance planning, cost-down opportunities, and production feasibility. His experience covers PM gears, automotive components, structural parts, and practical DFM support for long-run manufacturing programs.
Continue Reading
FC-0208 Material Guide: Properties, Applications, and When to Use It in Powder Metallurgy
9 min read
Material SelectionMetal Injection Molding Materials: Stainless, Low-Alloy, Tool Steel, and Specialty Alloys for MIM
9 min read
Material SelectionCopper Powder Types for Powder Metallurgy: Electrolytic vs Atomized vs Reduced
8 min read
